⇚ На страницу книги

Читать All sciences. №2, 2023. International Scientific Journal

Шрифт
Интервал

Authors: Aliyev Ibratjon Xatamovich, Qo'ldashov Obbozjon Xokimovich, Yakubov Inom Daniyarovich, Yusupov Yarash, Vavilova Ekaterina Aleksandrovna, Abduraxmonov Sultonali Mukaramovich, Sayitov Shavkat Samiddinovich


Editor-in-Chief Ibratjon Xatamovich Aliyev

Illustrator Ibratjon Xatamovich Aliyev

Illustrator Obbzojon Xokimovich Qo'ldashov

Illustrator Sultonali Mukaramovich Abduraxmonov

Cover design Ibratjon Xatamovich Aliyev

Cover design Ra'noxon Mukaramovna Aliyeva

Scientific director Boxodir Xoshimovich Karimov

Economic Director Farruh Murodjonovich Sharofutdinov

Economic Consultant Botirali Rustamovich Jalolov

Proofreader Sultonali Mukaramovich Abduraxmonov

Proofreader Obbozjon Xokimovich Qo'ldashov

Proofreader Ekaterina Aleksandrovna Vavilova


© Ibratjon Xatamovich Aliyev, 2023

© Obbozjon Xokimovich Qo'ldashov, 2023

© Inom Daniyarovich Yakubov, 2023

© Yarash Yusupov, 2023

© Ekaterina Aleksandrovna Vavilova, 2023

© Sultonali Mukaramovich Abduraxmonov, 2023

© Shavkat Samiddinovich Sayitov, 2023


ISBN 978-5-0059-7572-0 (т. 2)

ISBN 978-5-0059-5900-3

Created with Ridero smart publishing system

PHYSICAL AND MATHEMATICAL SCIENCES

ABOUT THE USE OF THREE-DIMENSIONAL PRINTERS IN ARCHITECTURE

UDK 004.356.2

Aliev Ibratjon Khatamovich


2nd year student of the Faculty of Mathematics and Computer Science of Fergana State University


Ferghana State University, Ferghana, Uzbekistan

Аннотация. Развитие современных технологий ведёт к совершенствованию большого вида привычных на сегодняшний день методов и способов сооружения зданий, но как известно всё более популярными являются методы использования трёхмерных принтеров для достижения этих целей. Подобная идея была активно разработана ранее, но для этого использовалась либо одна головка, либо несколько установок для одного здания, более того, такая технология не позволяла сооружать двух, трёх и т. д. этажные здания. Но кажется решение подобной проблемы было приведено на примере модели небольшого здания в одном из произведений.

Ключевые слова: архитектура, трёхмерные принтеры, технологии, строительства, методы, устройства.

Annotation. The development of modern technologies leads to the improvement of a large number of methods and methods of building construction that are familiar today, but as is known, methods of using three-dimensional printers to achieve these goals are becoming increasingly popular. A similar idea was actively developed earlier, but either one head or several installations for one building were used for this, moreover, such technology did not allow the construction of two, three, etc. storey buildings. But it seems that the solution to such a problem was given by the example of a model of a small building in one of the works.

Keywords: architecture, three-dimensional printers, technologies, construction, methods, devices.

Initially, it is worth pointing out that the structure model, namely one power plant, consists of 6 power generation units. They have 6 buildings for linear acceleration, 6 blocks for cyclotrons and also 6 blocks for power output, that is, in total, you need to create 18 buildings connected to each other. The hall of the linear accelerator itself, which is located at a depth of 12 meters, has a size of 10 meters in length and 4 meters in width, the height is about 3 meters. Directly above it, after 2 floors of the basement, the 1st floor begins and the same hall, but for the control panel of the linear accelerator.